How to Plumbing – Installing a New Faucet Can Be a Difficult Task
- by siteadmin
A plumbing system is a network of pipes that bring fresh water into buildings and carry wastewater away. They are found in homes, offices, and factories.
When writing a how-to guide, keep instructions short and to the point so readers can follow them easily. Include visual representations and examples for easier comprehension.
Draining the Pipes
Water pipes are usually the first thing that get taken for granted in most homes. They are installed in kitchen sinks, showers and toilets, and they carry running water throughout the home.
But if not properly drained, these pipes could freeze when temperatures dip below freezing and cause plumbing issues. The leftover liquid will expand as it freezes, creating pressure that leads to bursting and leaks.
If you're planning on making any changes to your home's plumbing system, be sure to drain the pipes before completing the project. You'll save yourself from a lot of hassle and damage when you do so.
Draining the pipes is not part of every residential plumbing project, but it's important to know how to do it before a problem occurs. This way, you'll be prepared for any plumbing problems or emergencies and can schedule drain maintenance at a later date if necessary.
Installing a Faucet
When it comes to plumbing, a new faucet can dramatically change the look of your bathroom or kitchen. Choosing a new one can be difficult, however.
The first thing to consider is the type of sink you have. There are single, two, or three-hole options.
You can also choose from a wide range of finishes. Chrome, for example, can start at $40, while top-of-the-line finishes can run up to $1,200 or more.
Once you've decided on a faucet, the next step is to connect it to the water supply lines underneath the sink. Some new faucets have flexible piping already attached, which makes this easy.
If the faucet you're installing does not have these, you'll need to attach flexible supply lines and hook them up to your hot and cold water valves underneath the sink. Make sure to wrap the threads of the valves with a strip of Teflon plumber's tape before connecting them. This will give them a tight seal and prevent leaks.
Installing a Toilet
If you are a novice, installing a toilet may be a daunting task. It involves understanding plumbing principles and using the right tools to make sure the job is done correctly.
First, you'll need to remove the old toilet. This will prevent sewer gas from entering the bathroom and keep odors from filling it.
Next, use a putty knife to scrape off the old wax ring from the floor flange (the hole in the floor under the toilet). It's best to take your time and do this thoroughly.
Once the flange is free, place your new toilet bowl onto the flange and lower it into place. It's important to align the holes in the base of the bowl with the bolts in the flange.
Then, place a washer and nut over each closet bolt on the toilet bowl and hand tighten. The nut should be snug, but not too tight as this could crack the porcelain bowl.
Installing a Shower
Whether you have an old shower surround, bathtub or tub/shower alcove that needs renovating or you're building a new home, learning to install a shower is a great project for the DIY homeowner. The process is relatively easy, especially if the shower panels you use come as prefabricated units with flattened edges called flanges that can be nailed to the wall studs.
Before you begin putting in the base of the shower, square up and plumb the walls with a level. If the walls are uneven or lean, you'll need to remove some framing studs and replace them with new ones.
Once the walls are level and straight, lay the shower base against a corner of the room to ensure that it is horizontally and vertically plumb. If the bubble of the level is not within the two center lines, use wood shims under the base to lift it slightly.
Next, screw the shower base to the studs every 6 inches or so using screws. This will help the flanges sit flush against the studs and secure the pan.
7004 Colonial Ct, North Wales, PA 19454
A plumbing system is a network of pipes that bring fresh water into buildings and carry wastewater away. They are found in homes, offices, and factories. When writing a how-to guide, keep instructions short and to the point so readers can follow them easily. Include visual representations and examples for easier comprehension. Draining the Pipes…
Recent Posts
- How to Create a Safe and Welcoming Environment in Lexington Shelters
- Why You Should Invest in a Salon Treatment for Your Hair in Houston
- All Temp Air Conditioning & Refrigeration Offers Top-Notch Refrigerator Repair Services in Tampa
- How Long Does Dishwasher Repair Typically Take, And What Is The Expected Cost?
- How Long Will Dishwasher Service Take? And What Should I Expect to Pay?